The two primary functions of sway bars are to control body roll and to determine the understeer or oversteer behavior of a vehicle. Stock sway bars have low torsional spring rates because they are manufactured from small diameter bar stock or tubing. BMR Suspension’s SB334 adjustable front and rear sway bar kit was designed by factoring in the vehicle weight, application, motion ratio, coil spring rate, and adjustability requirements. Manufactured from heavy-duty 38mm DOM steel tubing, the SB334 is cold formed to better resist torsional fatigue and retain its "memory" far longer than the hot-formed bars used by many competitors. The sway bar is CNC-formed for exact manufacturing tolerances and repeatable high quality. Thrust washers are welded to the front bar to locate the sway bar bushing mounts. This is critical as it properly locates the sway bar and prevents lateral movement during hard cornering maneuvers The SB334 attaches to your 82-92 F-Body with polyurethane bushings, reducing the deflection from the stock rubber bushings. These bushings are made from low-deflection polyurethane with a 88-durometer hardness, and feature internal flutes to retain grease for optimal performance. BMR Suspension designed the SB334 front sway bar kit for street performance, autocross, and road race applications. The front adjustable sway bars’ two positions give you the versatility to drive to and from the road course or autocross and still out handle the competition with the same sway bar.
The two primary functions of sway bars are to control body roll and to determine the understeer or oversteer behavior of a vehicle. Stock sway bars have low torsional spring rates because they are manufactured from small diameter bar stock or tubing. BMR's suspensions SB334 adjustable front and rear sway bar kit was designed by factoring in the vehicle weight, application, motion ratio, coil spring rate, and adjustability requirements. Manufactured from heavy-duty 38mm DOM steel tubing, the SB334 is cold formed to better resist torsional fatigue and retain its "memory" far longer than the hot-formed bars used by many competitors. The sway bar is CNC-formed for exact manufacturing tolerances and repeatable high quality. Thrust washers are welded to the front bar to locate the sway bar bushing mounts. This is critical as it properly locates the sway bar and prevents lateral movement during hard cornering maneuvers The SB334 attaches to your 82-92 F-Body with polyurethane bushings, reducing the deflection from the stock rubber bushings. These bushings are made from low-deflection polyurethane with a 88-durometer hardness, and feature internal flutes to retain grease for optimal performance.
BMR's suspension designed the SB334 front sway bar kit for street performance, autocross, and road race applications. The front adjustable sway bars two positions give you the versatility to drive to and from the road course or autocross and still out handle the competition with the same sway bar. This sway bar gives you a 165%-189% increase in sway bar rate over the stock bar. The adjustability and rate increases allow you to fine-tune the handling characteristics of your 82-92 F-Body so you can drive harder through corners with minimal body roll. The hollow design allows for loads of strength in the lightest package possible. This means increased performance with no sacrifices. The SB334 front sway bar kit by BMR's suspension attaches to your Third Gen F-Body with 88-durometer polyurethane bushings, resulting in improved sway bar control and handling. When performance is a must, rely on BMR's suspension!BMR's suspensions SB334 front sway bar kit is available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 2-3 hours. Proudly made in the U.S.A.!
This sway bar gives you a 165%-189% increase in sway bar rate over the stock bar. The adjustability and rate increases allow you to fine-tune the handling characteristics of your 82-92 F-Body so you can drive harder through corners with minimal body roll. The hollow design allows for loads of strength in the lightest package possible. This means increased performance with no sacrifices. The SB334 front sway bar kit by BMR Suspension attaches to your Third Gen F-Body with 88-durometer polyurethane bushings, resulting in improved sway bar control and handling. When performance is a must, rely on BMR Suspension!BMR Suspension’s SB334 front sway bar kit is available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 2-3 hours. Proudly made in the U.S.A.!
BMR Suspension designed the SB334 sway bar kit for street performance, autocross, and road race applications.
BMR 82-92 Chevrolet Camaro Sway Bar Kit Front Hollow 38mm Adjustable - Black Hammertone
Coil Spring / Tie Rod Sleeve / Stabilizer Bar Kit
Sway Bar Kit, Front, Hollow 38mm, Adjustable
BMR Suspension - SB334H
Sway Bar Kit
